Distributed cache updating dynamic source routing protocol ppt Free online ai sex chat
Module parameters can be specified in two ways: via the kernel command line with a module name prefix, or via modprobe, e.g.: Parameters for modules which are built into the kernel need to be specified on the kernel command line. DRM Direct Rendering Management support is enabled. Possible values are: fullflush - enable flushing of IO/TLB entries when they are unmapped.modprobe looks through the kernel command line (/proc/cmdline) and collects module parameters when it loads a module, so the kernel command line can be used for loadable modules too. DYNAMIC_DEBUG Build in debug messages and enable them at runtime EDD BIOS Enhanced Disk Drive Services (EDD) is enabled EFI EFI Partitioning (GPT) is enabled EIDE EIDE/ATAPI support is enabled. Otherwise they are flushed before they will be reused, which is a lot of faster off - do not initialize any AMD IOMMU found in the system force_isolation - Force device isolation for all devices. acpi_mask_gpe= [HW, ACPI] Due to the existence of _Lxx/_Exx, some GPEs triggered by unsupported hardware/firmware features can result in GPE floodings that cannot be automatically disabled by the GPE dispatcher. acpi_no_static_ssdt [HW, ACPI] Disable installation of static SSDTs at early boot time By default, SSDTs contained in the RSDT/XSDT will be installed automatically and they will appear under /sys/firmware/acpi/tables. Note that specifying this option does not affect dynamic table installation which will install SSDT tables to /sys/firmware/acpi/tables/dynamic. acpi_pm_good [X86] Override the pmtimer bug detection: force the kernel to assume that this machine's pmtimer latches its value and always returns good values. PARIDE The Par IDE (parallel port IDE) subsystem is enabled. acpi_irq_balance [HW, ACPI] ACPI will balance active IRQs default in APIC mode acpi_irq_nobalance [HW, ACPI] ACPI will not move active IRQs (default) default in PIC mode acpi_irq_isa= [HW, ACPI] If irq_balance, mark listed IRQs used by ISA Format: ... align_va_addr= [X86-64] Align virtual addresses by clearing slice  when allocating a VMA at process creation time.
acpi_force_table_verification [HW, ACPI] Enable table checksum verification during early stage.
Format: Support masking of GPEs numbered from 0x00 to 0x7f. acpi_os_name= [HW, ACPI] Tell ACPI BIOS the name of the OS Format: To spoof as Windows 98: ="Microsoft Windows" acpi_rev_override [ACPI] Override the _REV object to return 5 (instead of 2 which is mandated by ACPI 6) as the supported ACPI specification revision (when using this switch, it may be necessary to carry out a cold reboot _twice_ in a row to make it take effect on the platform firmware). # disable all built-in OS vendor strings acpi_osi=!! For broken n Force2 BIOS resulting in XT-PIC timer.
This facility can be used to prevent such uncontrolled GPE floodings. acpi_rsdp= [ACPI, EFI, KEXEC] Pass the RSDP address to the kernel, mostly used on machines running EFI runtime service to boot the second kernel for kdump. acpi_sci= [HW, ACPI] ACPI System Control Interrupt trigger mode Format: acpi_skip_timer_override [HW, ACPI] Recognize and ignore IRQ0/pin2 Interrupt Override.
You can choose your language settings from within the program.
The following is a consolidated list of the kernel parameters as implemented by the __setup(), core_param() and module_param() macros and sorted into English Dictionary order (defined as ignoring all punctuation and sorting digits before letters in a case insensitive manner), and with descriptions where known. 32: only for 32-bit processes 64: only for 64-bit processes on: enable for both 32- and 64-bit processes off: disable for both 32- and 64-bit processes alloc_snapshot [FTRACE] Allocate the ftrace snapshot buffer on boot up when the main buffer is allocated.
Our Word of the Year choice serves as a symbol of each year’s most meaningful events and lookup trends.